A genuine must have for all your engine overhauls!
A fantastic tool for pressing the crankshaft bearings in with all CY and Zenoah engines. T his tool can be pressed together with a vise or screwed together using the bolt that is included, screws together with a HPI Baja wheel nut wrench or 24mm socket.
Complete set of DDM Hex Driver Bits, including 5 standard bits (2mm,2.5mm,3mm,4mm,5mm) and 3 ball-end bits (3mm,4mm,5mm).
Includes both types of handles (standard, and magnetic 2-in-1 T-handle for extra torque), as well as 2 extra socket holders for your drill
Everything you need to complete a great hex tool set for your HPI Baja, Losi 5ive, Redcat, FG, MCD, etc.
DDM 2-in-1 Hex Driver Handle for 1/4" Drivers.
This weighted, magnetic bit handle will give you all the flexibility you need. Use it as a regular handle, or but the bit in the middle to increase leverage. The hex driver bits are held into place by a magnet in the center of the handle.
These handles fit our DDM hex drivers of both types (standard and ball end). Make your job easy and swap out bits in seconds!
Note: This is the handle only, drivers (bits) are sold separately
Set of three hardened steel allen bits for electric drills and hand tools.
Each bit is 6.25 inches (160mm) in length. These are 1/4" shaft size, and compatible with electric drills and hand tools that accept 1/4" bits.
Sizes include 3.0 ,4.0, 5.0mm
Note: Ball ends allow for working at angles, but are not as strong as the standard straight design. It is possible to break a ball end if too much pressure is used.
Set of five hardened steel allen bits for electric drills.
Each bit is 6.25 inches (160mm) in length. These are 1/4" shaft size, and compatible with electric drills and hand tools that accept 1/4" bits.
Sizes include 2.0, 2.5 ,3.0 ,4.0, 5.0mm
Set of six (6) hardened steel TORX star bits for electric drills. Sizes include:(T10, T15, T20, T25, T27, T30)
Each bit is 6.25 inches (160mm) in length. These are 1/4" shaft size, and compatible with electric drills and hand tools that accept 1/4" bits.
The DDM hand tools ( part numbers ca197a and ca197b) are fully compatible.
DDM Hex Bit Holder w/Handle for 1/4" Drivers.
These nice handles fit our DDM hex drivers of both types (standard and ball end). Make your job easy and swap out bits in seconds!
Note: This is the handle only, drivers (bits) are sold separately
DDM Socket Holder Adapter for 1/4" Hex Drivers.
These fit both types of our 1/4" drivers (standard and ball-end) and give you greater flexibility when working with your drivers. You can insert this holder into your drill or hand-tool and quickly replace bits by just pulling them out, making your job faster and easier.
The perfect unit for monitoring all your batteries to ensure that they are in peak condition when you come to use them.
Works great on receiver packs too. So now you can instantly tell if you have enough charge to safely use your car.
New and updated, the Etronix Soldering Jig now features an extended foot plate with adjustable helping crocodile clip grip for even more useful multi-tasking jobs.
Now you can solder like a pro all those different connectors and leads without worrying about how to hold everything and not burn yourself in the process.
Fastrax .10/.15 Crankcase Bearing Insertion and Removal Tool.
Makes quick work of inserting or removing engine bearings.
Fastrax .21 Crankcase Bearing Insertion and Removal Tool.
Makes quick work of inserting or removing engine bearings.
Need to make a threaded hole trackside? Make it properly with these Hand Taps.
Need to make a threaded hole trackside? Make it properly with these Hand Taps.
The only way to remove and fit clutch springs and shoes to your nitro engine. No more damage to your hands or the engine itself.
Simple to use, comes with instructions.
A must have for bodyshell, spoiler and other general use.
These scissors feature a finer point especially suited to tyre tuning. Suffering too much traction? Then use the Fastrax Tyre Tuners to snip off some outer spikes to either fully or half their height and lessen traction. The smaller point make these scissors a must and very accurate when trimming tyres.
Helpful tool for disassembling clutch shoes, flywheels...
This is the 12 pieces RC Metric Foldup Pocket tool kit form Hot Racing
The Always Ready Foldup tool is always right by your side when you need it.
Stainless steel magnetized e-clip pliers.
Easily install or remove e-clips with these stainless steel and magnetized e-clip pliers. Magnetized to hold the clip until pressure is applied and hooked at the end for pulling or removing clips as well..
- Box joint structure for long life and to avoid loosening
- Magnetic Slit Point
- RoHS Compliant
- 150mm Model 01 suitable for Clip Size 3-5mm
- 165mm Model 02 suitable for Clip Size 7-9mm
Stainless steel magnetized e-clip pliers.
Easily install or remove e-clips with these stainless steel and magnetized e-clip pliers. Magnetized to hold the clip until pressure is applied and hooked at the end for pulling or removing clips as well..
- Box joint structure for long life and to avoid loosening
- Magnetic Slit Point
- RoHS Compliant
- 150mm Model 01 suitable for Clip Size 3-5mm
- 165mm Model 02 suitable for Clip Size 7-9mm
Until now the only way to tighten or remove the pinion screw on a Losi 5ive is tiohold it with a pair of pliers. Doing this can damage your pinion.
Team FastEddy now offers Pinion Wrenches for the Losi Five. Made of 1/8th inch stainless steel they are up to the task or removing even the tightest of pinion bolts without damaging your gear. They also make installing your pinion a snap.
Offered in all the popular gear sizes.
Stainless steel plates that cover both the exhaust port and the intake port on your RC Gas Engine.
Contamination is the largest engine killer. Its always best to cover your posts when the intake or exhaust is removes. Works great for storing engines.
The Triple A Racing engine stand. Perfect for safely keeping an displaying spare engines or as a useful work stand when maintaing your engine.
Don't just leave that spare engine rattling round on your workbench!! Fit a Triple A Racing stand to it then neatly store it away.
